Mold Release Sprays from Slide Products

Item #: SL40012N
Paintable light-duty biodegradable mold release agent - Aerosol Economical Paintable mold release requires no special cleaning. It will not interfere with part bonding, heat sealing, laminating, ultrasonic welding or post-decorating operations. You get perfect finishes every time and more cycles per can over other comparable releases. • No chlorinated solvents • Light-duty • Get a perfect finish • Paint, plate and hot-stamp over it • No spalling & no fish-eyes • Recognized by UL • Maximum operating temperature: 650ºF

Item #: SL40810P
ECONO-SPRAY 3 MOLD RELEASE

Item #: SL41612N
EconoMIST silicone mold release agent - Aerosol Contains the same high-quality ingredients as premium Silicone Release except formulated to be used for light-duty applications. For hard to release parts use No. 40112N Silicone Release. • No chlorinated solvents • NSF category M1 • Light duty silicone release • UL recognized • Maximum operating temperature: 600°F

Item #: SL46612N
Knock Out non-silicone, paintable mold release - Aerosol Knock Out is the mold release that works where others have failed. It gets “sticky parts” cleanly out of the mold and is approved for indirect food contact. Knock Out mold release imparts a light, dry coating that is amazingly effective, working for several cycles without re-application. • No chlorinated solvents • Paintable, non-silicone • Food-approved release agent(*****) • Maximum operating temperature: 450°F (*****) FDA regulation 21 CFR 178.3570 (GRAS)

Item #: SL40710
Econo-Spray 2 Mold Release Agent - Aerosol Econo-Spray® 2 is a paintable release in a non-chlorinated solvent carrier system. It permits post-decorating of molded parts without prior cleaning. • No chlorinated solvents • Paintable • Maximum operating temperature: 650ºF

Item #: SL41012N
Zinc Stearate Mold Release Agent - Aerosol A dry, light, water-repellent powder, Zinc Stearate is economical to use and gives better finishes. Use it for polycarbonates, polypropylenes, polysulfones and rubber molding. Compatible with oil-based paints, its formulation results in fewer rejects and lower production costs. • No chlorinated solvents • Non-silicone paintable • Lubricant powder • Maximum operating temperature: 600°F

Item #: SL54912
Heavy-Duty Mold Release and Pin Lube - Aerosol An ideal lubricant for the front half of ejector pins (pins in forward position), this almost dry lubricant minimizes the possibility of leaching out onto molded parts. Use in combination with application of Super Grease on back side of ejector pins. Stable at temperatures up to 450°F. Heavy-Duty Mold Release and Pin Lube can be used on plastics, rubber, waxes, glass-filled nylon and similar materials. • No chlorinated solvents • Non-silicone • Paintable • Food-approved lubricant(*****) • Dry release minimizes leaching out onto parts • Maximum Operating Temperature: 450°F (****) FDA regulation 21 CFR section 182.20; 21 CFR section 182.60; 21 CFR section 172.515

Item #: SL40510
Econo-Spray 1 Mold Release Agent - Aerosol Econo-Spray® 1 contains a highly effective, non-paintable silicone fluid in a non-chlorinated solvent carrier system. It will give an excellent release with all thermoplastics. • No chlorinated solvents • Non-paintable silicone • Recognized by UL • Maximum operating temperature: 600ºF

Item #: SL40112N
Silicone Mold Release Agent Get more cycles per spray, more cycles per can, with Slide’s Silicone high-quality, pure silicone-oil mold release. Keeps the most challenging parts from hanging up and stalling production. Extremely effective for injection and compression molding. (++) Lubricants are suitable for food contact use as indicated in Title 21 of the Code of Federal Regulations. The appropriate sections for release agents are 175.300, 177.2600, 178.3570 and 181.28. Federal Definitions and Standards of identity for Food CFR 121.101 (G.R.A.S.). • No chlorinated solvents • Food-approved lubricant(++) • Faster molding & more production • Approved for food packaging machinery • Recognized by UL • Maximum operating temperature: 600ºF

Item #: SL45712N
Pure Eze mold release agent - Aerosol Pure Eze is a white, oil-based, food-approved release ideal for medical and food applications. Use Pure Eze with all thermoplastic resins, polyolefins, polycarbonates, rubber and some epoxies. It is colorless, odorless, tasteless and will not change color over time. • No chlorinated solvents • Food-approved lubricant, no lecithins(+++++) • Neutral white oil-based release • Won’t turn color or turn rancid • Paintable, non-silicone • An excellent all-purpose release • Recognized by UL • Maximum operating temperature: 600ºF (+++++) Meets or exceeds FDA and USP/NF requirements for 21 CFR 172.878, 21 CFR 178.3620 and 21 CFR 573.680